Penetrating Damp Treatment

Guide · Homeowners · 4 min read · Updated 17 November 2026

Penetrating Damp: What You Can Fix Yourself and What You Can't

Short answer

Simple ground-level jobs such as clearing a single-storey gutter, refixing a downpipe, clearing weep holes and keeping soil away from walls are reasonable DIY. Repointing, render repairs, roof and chimney work, cavity problems and basement waterproofing are best left to professionals, because they need the right materials, access equipment and experience to avoid making damp worse.

Penetrating Damp: What You Can Fix Yourself and What You Can't

Start with the diagnosis

Whether you do the work yourself or hire someone, the first step is to be sure where the water is getting in. Map the damp inside, check the outside directly above and around it, and look during heavy rain if you can. A fix aimed at the wrong defect wastes time and money and can delay the real repair until the damage is worse.

If you cannot see an obvious cause, or the source is high up, a professional inspection is usually worthwhile before any DIY.

Think about how long the problem has been going on. A damp patch that appeared last week after a storm is probably a single defect. One that has grown over several winters may have caused hidden damage, such as rotten window frames, joist ends or roof timbers, that needs a professional to assess.

Jobs most homeowners can do

Some causes of penetrating damp are simple maintenance tasks. Clearing leaves and moss from a gutter you can reach safely from a stable ladder, flushing a blocked downpipe, refitting a loose downpipe section or replacing a failed shoe at the bottom are all straightforward. So is clearing paint or soil from weep holes and pulling flower beds and stored items away from the wall.

Even simple jobs deserve care. Wear gloves when clearing gutters, use a scoop rather than bare hands, and avoid pressure washers on old brickwork, which can drive water into the wall and wash out soft mortar.

  • Clearing single-storey gutters from a stable ladder
  • Flushing blocked downpipes and hoppers
  • Refitting loose downpipe sections and brackets
  • Clearing weep holes and air bricks
  • Moving soil, planters and stored items off walls
  • Checking sealant around ground-floor window frames

Jobs best left to professionals

Repointing looks simple but is easy to get wrong. Using cement mortar on soft brick or stone, or pointing that sits proud of the brick face, can trap water and damage the wall. Render repairs need the right mix and thickness and proper detailing at sills and beads. Roof, valley, flashing and chimney repairs involve working at height and specialist leadwork. Cavity clearing, cavity tray replacement and basement waterproofing all need specialist knowledge and tools.

The cost of getting a complex repair wrong is usually far higher than the cost of a professional doing it right the first time. A failed DIY render patch, for example, may need cutting out and redoing by a contractor anyway, adding to the final bill.

RepairDIY or professionalTypical professional price
Gutter and downpipe repairDIY at ground level; pro above£120–£450
RepointingProfessional£45–£90 per m²
Render patch repairProfessionalfrom £250
Full re-renderProfessional£50–£95 per m²
Chimney flashing and pointingProfessional£350–£1,200
Basement waterproofingProfessional£90–£180 per m²

DIY mistakes that make damp worse

Several common DIY fixes trap water rather than keeping it out. Silicone sealant spread over cracks in render or brickwork stops the wall drying and often fails within a season. Waterproof paints and coatings applied to older solid walls can hold moisture inside, leading to spalling bricks and damp inside. Internal tanking or waterproof paint inside the house hides symptoms while the wall keeps getting wetter.

Masonry water-repellent creams can be useful on sound brickwork in exposed positions, but they are not a substitute for repairing cracks or eroded pointing, and they should not be used on walls that need to breathe without specialist advice.

Safety first

Falls from ladders are a common cause of serious injury at home. Only work at heights you are comfortable with, on a stable surface, with someone footing the ladder. Never lean out sideways or work on a roof without proper equipment. If a gutter is above a conservatory or a flat roof, or the repair is at second-floor level, leave it to a contractor with towers or scaffolding.

Where scaffolding needs to stand on a public pavement, the contractor normally applies for a licence from the local highway authority, so allow time for that.

Choosing a contractor

Pick someone who works regularly on your type of building. Older solid-walled homes need contractors comfortable with lime mortar and lime render. Ask what they think is causing the damp and why, what materials they will use and how they will detail edges, sills and junctions. Ask for a written quote that lists the work, area and materials, and whether scaffolding and any licence are included. A good contractor will explain the repair rather than just offering a treatment.

A sensible maintenance routine

Most penetrating damp can be prevented with a little regular attention. Clear gutters in late autumn once the leaves have fallen, and check them again in spring. Walk around the house after storms and look for slipped tiles, lifted flashing or debris in valleys. Each year, check pointing, render and window sills on the most exposed elevations. Catching small defects early means repairs stay cheap and simple.

  • Late autumn: clear gutters and downpipes
  • After storms: check roof, ridge and flashings from the ground
  • Spring: inspect pointing, render and sills
  • Every few years: professional roof and chimney inspection

Questions people also ask

Can I use a waterproof sealer on my brick wall?

Breathable water-repellent creams can help on sound brickwork in exposed locations, but they will not fix cracks or failed pointing. Avoid non-breathable coatings on older solid walls, because they can trap moisture and cause frost damage. Repair the defects first and get advice before treating the whole wall.

Is repointing a DIY job?

Small areas at ground level can be done by a careful DIYer, but it is easy to use the wrong mortar or finish the joint badly. On older buildings, lime mortar is usually needed. For larger areas, or work at height, a professional will do a better and longer-lasting job.

Should I paint over a damp patch while I wait for repairs?

It is better to wait. Painting over damp seals it in and the paint will usually blister or stain again. Fix the cause first, let the wall dry, then use a stain block and breathable paint. In the meantime, keep the room ventilated and move furniture away from the damp area.

Written and checked by the Penetrating Damp Treatment team. Read our editorial policy.

Get a free penetrating damp treatment quote

Tell us what you need and we'll come back with a clear price.

Request a quote